-
UA, burn him
Post your reloading setups!
Help folks learn how to configure their reloading rooms. Post pictures if you can.
#Dillon650
#Dillon550
#Dillon1050
Last edited by LittleLebowski; 04-12-2017 at 12:54 PM.
#RESIST
-
Member
Words cannot express how happy this makes me. Tagged.
-
Member
My setup:
Hornady L-n-L AP press
Cheapo Lee balance beam powder scale; my understanding is that unless you want to go expensive, digital scales are not accurate or consistent enough to be worthwhile
Midsouth's tumbler/media separator kit, though just about any brand will do, and wet tumbling with stainless steel pins would be nicer
RCBS Dies, because that's what my father in law recommended way back when; if I had it to do over again, I'd get Hornady, because I like their lock rings better
Hornady Powder Cop die as a safety check
An empty gallon milk jug to catch the spent primers.
Small tools:
Primer pocket cleaner (this doesn't get much use, but it was very cheap, so whatever)
Primer pocket reamer for when I run into crimped (military) cases
Chamfer/deburr tool
I've got 4 small primer pickup tubes, and I probably should get some more. The more you have, the more you can load before you have to putz around loading primer tubes. I "customized" my primer pickup tubes by putting some closed-cell foam grip things that are intended for handicapped people to use on small implements on them. This made them much less painful to use. (I found my hand would cramp up trying to load primer tubes, and the larger grip makes the process much more comfortable.)
While lubing cases isn't strictly necessary for pistol rounds, I find that giving them a blast of Hornady One Shot case lube makes the press run smoother, which results in more consistent OALs.
I'd like at some point to get a powder-through expander die so that I can go to separate seat and crimp dies; while seating and crimping in one step works, it's much more fiddly to get set up properly than doing it in two separate steps.
I have not bothered with a case feeder or a bullet feeder. While they seem like they'd be really nice, the cost has been tough to justify at my loading volume. For someone loading thousands of rounds/month, they'd make perfect sense, as it would speed up and smooth out the process, in addition to reducing the amount of stuff you have to touch.
I'm sure I'm forgetting some stuff here, but that's the basics; a press, a scale, a tumbler, and appropriate dies.
If I ever get into loading rifle rounds, I'll have to add a case trimmer, but for straight-wall pistol cases, it's not really needed.
-
Hokey / Ancient
I need to rebuild it since moving from KC; I'll post pictures when I do. Standard deal is an 8' bench, 2' deep, 2" thick, on metal legs at 4' off the floor. RL550 is on a strong mount 18" from the left edge.
Bullets sit in a shallow dish to the left of the machine; brass is in a salad bowl to the right. A little pocket electronic scale is to the right of that. Primer tubes are in a coffee mug behind the bullets, and a can of compressed air is kept close at hand too. Under the bench is the tumbler, media, brass, and big boxes of bulk bullets and hoarded loaded ammo.
There is space for pack and inspect to the right of the scale with a towel. To the right of that is usually a cheap single stage for resizing rifle brass, a case trimmer, and an automatic scale for precision rifle loads. I will probably not set that up unless I find a good rifle range in Dallas.
Other than that you need a lot of shelves. Caliber conversion kits, dies, primers,powder, small lots of bullets and brass, empty boxes, and full boxes.
There is literally nothing in the world more satisfying than a five gallon bucket full of .45.
-
UA, burn him
-
Site Supporter
-
Member
Oh, in case anybody wanted to know about the foam grip things I put on my primer pickup tubes, here's a link: http://www.amazon.com/Abilitations-A.../dp/B0042SWPKE. Those are the exact ones I'm using. They tend to slide a bit on small primer tubes; I need to find a way to keep them still and they'll be just right. I don't load anything that needs large primers, but I bet they'd slide less on the slightly larger tube.
-
Site Supporter
Another Big Blue fan here. My reloader is a Dillon XL650. I load almost exclusively volume 9mm. It's the only press I've owned. I took a bit of a chance when getting into the game and bought the press I thought I'd want down the road. 5 or so years later, I can say it was absolutely the best decision I could have made. The prospect of learning on a progressive wasn't nearly as hard as I'd envisioned and I haven't had to "buy twice". (Although I'm admittedly really tempted to invest in a super 1050 and then explore the auto drive world )
Buying the 650 was probably the best monetary investment to date I've made in my shooting. I have it set up with a case feeder and can't imagine loading without it now. If I had to do it again, I'd purchase the case feeder first thing with the machine. I'm thinking seriously about investing in a bullet feeder too, but I'll probably wait until I make the 1050 upgrade decision before going down that road. The fact of the matter is I can currently load a legit 900 to 1000 rounds an hour, taking my time (assuming brass is clean and ready and primer tubes are loaded; see below) and my shooting volume during the shooting season is only 2000k/month or so.
I also use a powder check die. I pay really close attention when I'm loading but this thing is worth it's weight in gold. EVERYBODY f*cks up occasionally. This potentially catches those botches, limiting the likelihood that you're gonna get a squib or a double charge and blow up your gun.
I bought an auto primer filler (Dillon RF 100) more recently. It's another addition I'd absolutely recommend. While it sounds kinda silly, it's SOOO nice not to have to use the flip tray and filler tubes. While kinda pricey, it's worth every penny and allows the actual loading process to be all that much more efficient. Highly recommend.
Other accessories:
-Roller handle (should just come standard)
-Large vibratory case cleaner
-Large case-media separator/tumbler
-Beam scale
-Caliper set
-Case sorting tray set (I use quite a bit of range brass)
-Corn media
-Case lube
-Inertia bullet puller
-3 or 4 5 gallon buckets for brass sorting, storage, etc…
-Copy of a Lyman Reloading Handbook or the like
-Chronograph
Some people claim to have a "man cave." Mine is complete with dirt floor and walls and was established old school-like solo with a jackhammer, a pick and a shovel over the course of a couple years. Makes me a lot less concerned with old primers spitting out onto the floor. Bench is hanging from the floor joists.
Here are a couple pics...
t
-
Member
-
Member
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules